Trouble-shooting Hard Drive Problems - Part 1

It is extremely important not to make or write any changes to data on the hard drive without first verifying the hard drive configuration. Therefore, the first priority when unable to access information on a hard drive is to verify all of the configuration information dealing with the suspect hard drive.

Partition Parameter
Value or Equation

Partition Status
Bootable

Starting Head
1

Starting Sector
1

Starting Cylinder
0

Partition Type
Bigdos (drives greater than 30 MB), otherwise DOS 12

Ending Head
Total Number of Heads -1

Ending Sector
Sectors per Track displayed in Volume Boot Sector

Ending Cylinder
Number of Cylinders set in CMOS - 2

Total # of Sectors
Number of Sectors displayed in Volume Boot Sector

Start Absolute Sector
Number of Sectors per Track in Volume Boot Sector

Boot Signature
55AA

Step One: Make sure that Micro-Scope detects the hard drive

In Micro-Scope, System Configuration, Compare Settings - check to make sure that there is not an asterisk beside the number of hard drives detected value. If there is an asterisk, either the CMOS is set incorrectly, or there is an electronic problem (controller, cable, drive).

Step Two: Compare the BIOS parameters against the drive partition information.

In Micro-Scope, System Configuration, System Information - note the information displayed for the hard drive, specifically the parameters for the drive in question. Compare these parameters to the parameters in the MBR display under Micro-Scope, System Configuration, Partition Display using the following formula:

System Information
Master Boot Record

Cylinders
Ending Cylinder + 2

Heads
Ending Head + 1

Sectors
Sectors Per Track

If the information does not match, either the partition information is corrupt, or the CMOS setup or controller BIOS setup (if one exists) is incorrect, or there is a problem communicating with the drive.

Step Three: Check the drive functionality

In Micro-Scope, Diagnostics, Fixed Disk Tests - check the information in the Fixed Disk Selected window. Make sure that the proper drive type, model, and native parameters are showing in this window. If any of the information is incorrect, there is an electronic problem. Check the cable, controller and drive, re-seating all connections, and repeat the above procedure. After correcting the electronic problem, perform a read test on the first 10 cylinders of the drive. If any errors occur, then this is the most likely cause of the drive failure. Perform a read of the entire drive to determine if the errors are electronic in nature, or physical in nature. Electronic problems will result in the errors displayed not always being the same type or in the same location on the drive. If the problem is electronic, replace the cable, controller, and finally drive electronics and repeat the read test until no errors occur. If the error is physical, use an INT 13 type editor (such as Norton Advanced Editor), to block the entire drive and write the information to a daisy chained drive set to the same parameters as the faulty drive.

The next step, after the drive passes the read test on the first 10 cylinders, is to check the original partition setup of the drive.

Step Four: Check for the physical location of the master boot sector and the volume boot sector.

In Micro-Scope, Utilities, Fixed Disk Editor - use the FIND feature to search the last two bytes of each cylinder for a boot signature (55 AA). The first location where a boot signature should be found would be at cylinder 0, head 0, sector 1 (the master boot sector). The second location where a boot signature should be found is at cylinder 0, head 1, sector 1 (the volume boot sector). It is also possible to use the FIND feature to locate the volume boot sector by searching for MSDOS (in DOS based systems) or MSWIN (in Windows95 systems).

If there is a duplicate copy of the master boot sector found before the location of the volume boot sector, then it is possible that a boot virus has infected the hard drive in the system. The Rebuild Master Boot feature of Micro-Scope will eliminate any boot sector virus. Be sure to boot the system to the Micro-Scope diskette and immediately do a cold reboot of the system after using the Rebuild Master Boot feature.

If the volume boot sector is found in a location other than cylinder 0, head 1, sector 1, count the actual number of sectors before the volume boot sector, and compare that value to the value for the sectors per track displayed in the partition table described in step 2. If the values match, the most likely cause of the system failure is an incorrect CMOS setup. In this case the CMOS needs to be reset to the values indicated by the partition table described in step 2, remembering to use the formula described in step 2 when doing so. If the values do not match, set the CMOS Sectors Per track to the number of sectors counted before the volume boot sector and continue to the next step.

Step Five: Check the partition tables to make sure they are correct

Reboot the system to Micro-Scope and go to System Configuration, Partition Tables. Check the information displayed in the master boot record to see if there is any obvious corruption (that is, excessively large numbers, all partitions non-bootable, etc.) If there is no obvious corruption in the master boot record, then perform step 2 again. If the information matches at this point, go to step 6. If the information does not match, then set the sectors per track in the Master Boot Record to the number of sectors per track currently set in CMOS, set the starting head to 1, starting sector to 1, and starting cylinder to 0, and write the information to the drive.

Step Six: Verify the Master Boot Sector information

Display the Volume Boot Sector and use the values for heads and sectors per track (on the right half of the screen) to perform step 2 again.

If the values match, then the volume boot sector is probably okay. If any values in the Master Boot Record do not match the table to the right, reset the values to match the values in the table, and write to the drive.

If the values still do not match, both the Master Boot Record and the Volume Boot Record are probably corrupt. At this point, e-mail Technical Support for help in this situation. Future articles will provide more insight into the repair procedure.

Step Seven: Check the FATs

Check to see if the first FAT starts on the sector just beyond the volume boot sector. Use the find feature in the Fixed Disk Editor to search for F8 FF FF in the first three bytes of each sector. The first occurrence should be on sector two of head one. Continue to search until the second FAT is found, indicated by the second occurrence of F8 FF FF. Note the location of the cylinder, head and sector of the second FAT.

Based on the start of the second FAT, and the start of the first FAT, calculate how many sectors are in the first FAT. If necessary, read each sector starting at the first sector of the first FAT, keeping a count of the sectors that have been read until F8 FF FF is seen in the upper left of the HEX display, which would indicate the start of the second FAT. After calculating the sectors per FAT, compare this value to the value in the volume boot sector. If the values match, the drive should be accessible through DOS at this point.

Step Eight: Attempt to access the drive

Boot to a DOS-bootable floppy diskette and attempt to access the drive. If the root directory and sub-directories on the hard drive are readable at this point, then attempt to boot to the drive. If the drive boots at this point, the problem has been corrected. If the drive is still not bootable, e-mail the Micro 2000 Technical Support department for help.

Disclaimer - The Micro 2000 Tech Tip is a free service providing information only. While we use reasonable care to see that this information is correct, we do not guarantee it for accuracy, completeness or fitness for a particular purpose. Micro 2000, Inc. shall not be liable for damages of any kind in connection with the use or misuse of this information.

Micro 2000 Inc has been helping to solve the day-to-day challenges that IT departments face in order to keep their businesses operational as well as profitable for over 14 years. The company's primary goal is to put the customer first - through feature-rich, simple-to-use IT tools that can help IT administrators manage their jobs more effectively.

For more advice and free articles be sure to visit: http://www.micro2000.co.uk

---

The Right Way To Discharge Capacitor In Switch Mode Power Supplies

Switch mode power supply contain some large filter capacitors that can hold dangerous charges even if the unit has not been used for several days. Typical values... Read More

The Importance of Ergonomic Products

Interestingly, ergonomics though sounds to be a modern and trendy phenomenon, its principles are based on primitive life style. It is a known fact that earlier generations... Read More

How to Shop for Inkjet Printer Cartridges

Keeping Shipping Costs DownWhen shopping for inkjet printer cartridges online keep in mind that postage can add significantly to the cost of a single inkjet cartridge. In... Read More

Where does technology come from?

Ever wonder where all the cool gadgets come from? Ever wonder who gets to try this stuff out first? Usually the war machine scientists get it first,... Read More

Whats In An LCD Display?

Who needs an LCD display? Well, if you're like me, having one huge hunk of a monitor sitting on your desktop is just not feasible. Not only... Read More

A Review of Refurbished Toshiba Laptops

Toshiba offers a few of their refurbished laptops in the "Clearance Store" of their official website toshibadirect.com. There you can purchase their laptops at 20-30% discounts, refurbished... Read More

Rear Projection TV Facts - Understanding the Pros & Cons of Rear Projection in the Home Theater

Rear Projection Television - An Affordable OptionA great deal of consumer appeal for Rear Projection TV systems arise out of the shear simplicity that this product offers... Read More

Used Laptop Computer: Your Quick Purchase Inspection Guide ? Part 3

Used laptop computers are everywhere these days. How can you sift through the mass of available used laptop computers to narrow your search down to the right... Read More

What You Should Know Before You Buy Computer Equipment

You will have many factors to consider when deciding on which computer equipment to buy. The bewildering amount of choices can seem overwhelming. This guide will help... Read More

Video Encryption

What is Video Encryption?Video Encryption is an extremely useful method for the stopping unwanted interception and viewing of any transmitted video or other information, for example from... Read More

RAM - What is It & Why You Need Plenty

This is the first article in the Understanding Your Computer series from aworldofhelp.com. Our goal is to help people understand how their computer works, not simply tell... Read More

A Look at Laser Toners

Laser toner is the ink for laser printers. It is an extremely fine synthetic powder (usually plastic) packed into a cartridge. You insert the cartridge into your... Read More

How To Choose The Best Student Laptop?

How To Choose the Best Student Laptop?Merchants are singing those three magic words again, 'Back to School' and the fallout is everywhere!Just as you're getting your deep... Read More

Does Size Really Matter In Our Digital Age?

Well, we've all seen the advert, but that's not what I want to talk about, so get that out of your head straight away. No, let's think... Read More

Testing Flyback Transformer - How to Test and When to Replace It

Nowadays, more and more monitor comes in with flyback transformers problems. Testing flyback transformers arenot difficult if you carefully follow the instruction. In many cases, the flyback... Read More

Review: Implementing the Google Search Appliance in an Intranet environment

Our corporate intranet is a non-framed environment with both Lotus Domino and IIS (.Net and classic ASP) applications and content. We have between 300,000-500,000 pages of web... Read More

Laptop Notebook ? Inexpensive Business Laptops

Laptop Notebook ? Your Portable OfficeIn much of today's business world, portability and mobility are the keys to success. Having a laptop notebook computer provides business men... Read More

Used Laptop Computer: Your Quick Purchase Inspection Guide ? Part 1

Used laptop computers are everywhere these days. How can you sift through the mass of available used laptop computers to narrow your search down to the right... Read More

Selecting an Ink Jet printer?With Low Operating Cost

Printer technology has made tremendous advances in the past five years. Speeds are up and print quality is great. Meanwhile, printer costs have declined.What has not improved... Read More

Power and Your PC

The power coming into a computer is the most critical component, and it may be one of the most overlooked. It is just taken for granted that... Read More

A Guide To Bar Code Reader Downloads

Bar code readers have proven themselves to be essential tools in modern day business. Establishments, both big and small, have started to rely on bar code readers... Read More

Learn How To Diagnose Power Supply Problems

The Power Supply convert's your regular household current into low DC voltage used by the computer. When this component fails,there is simply no activity going on wih... Read More

What is Over-clocking a Processor?

Q : What is over clocking?Overclocking is when you make your system processor run faster that its normal speed. This has many advantages and dis-advantages.Advantages : This... Read More

Cisco CCNA Certification: An Illustrated Guide To Ethernet CSMA/CD

When you're studying for your CCNA exams, you're going to study the theory of technologies we basically take for granted in networking. CSMA/CD is one of those... Read More

Batteries for Your Laptop

With technology advancing more every day, electronics have become smaller and more mobile. This includes computers. The laptop, or notebook computer is extremely popular these days and... Read More

Setting up a Network -- Wired or Wireless?

To Wire or Not to Wire Wireless networks are en vogue, but your installation won't be successful unless you chose the right type of network... Read More