Motorcycle Suspension Setup: Getting to Grips with a Black Art

Suspension Set-up: The basics

Whether you are a road rider or a racer correct suspension setup is the key to fast smooth riding and consistent lap times. To get the best out of your bike it needs to be set up for the conditions in which you will be riding. It is considerably easier to set the bike up for the Track as you know what conditions will be like for the next hour or so and thus you can dial in the optimum settings for the that particular situation.

To what extent you change your suspension settings will depend on whether your bike will also have to cope with riding on the road. Unlike Roads Tracks are generally smooth and grippy. So if you are only going to use the bike on the track you have the luxury of fitting harder springs and modifying the fork and shock internals. If you ride on the road as well as the track you will probably want to keep a certain comfort level and concentrate on just optimizing the current equipment

With incorrect suspension setup, tire wear is increased and handling suffers, which in turn can result in rider fatigue. Lap times can be dramatically slower and in extreme cases safety can be compromised. Hopefully the following guide will help you dial in your suspension for faster and safer riding both on and off the track.

Firstly you will need to check the Fork and Shock sag: this is the amount the forks and rear shock settle under load. To measure it do the following: push down on the forks a number of times to settle them, then mark the stanchion with a felt pen or put a cable tie where the dust seal is sitting. Next ask some for help to lift on the bars so the front wheel is just off the ground and measure the amount the forks have traveled down. This is the static sag (or unladen sag), This can be changed by adjusting the spring preload (more preload = less sag). Repeat the same process for the rear, this time measuring the distance from the wheel spindle to a fixed point on the tail. Now you are ready to begin setting up your suspension. The key is to do it a little at a time and make notes as you go. For road riding start with the wet track settings and work from there.

Basic Setup: Check the following

Forks sag 18-22 mm for dry track, 23-27mm for rain.

Shock sag 8-10mm for dry track, 10-14mm for rain.

Check chain alignment. If not correct, bike will crab walk and sprocket wear will be increased.

Proper tire balance and pressure, starting with 30psi front and 32psi rear (both dry and wet).

Steering head bearings and torque specifications - if too loose, there will be head shake at high speeds.

Front-end alignment. Check wheel alignment with triple clamps. If out of alignment, fork geometry will be incorrect and steering will suffer.

Crash damage, check for proper frame geometry.

Stock Suspension Tuning Limitations

Manufacturers plan on designing a bike that works moderately well for a large section of riders and usages. To accomplish this as economically as possible, they use valving with very small venturis. These are then matched to a very basic shim stack which creates a damping curve for the given suspension component. At slower speeds this design can work moderately well, but at higher speeds, when the suspension must react more quickly, the suspension will not flow enough oil, and will experience hydraulic lock. With hydraulic lock, the fork and/or shock cannot dampen correctly and handling suffers. The solution is to re-valve the active components to gain a proper damping curve. It does not matter what components you have, (Ohlins, Fox, Kayaba, Showa) matching them to your intended use and weight will vastly improve their action. Furthermore, if you can achieve the damping curve that is needed, it does not matter what brand name is on the component. Often with stock components, when you turn the adjusters full in or out, you do not notice a difference. In part, this is due to the fact that the manufacturer has put the damping curve in an area outside of your ideal range. Also, because the valves have such small venturis, the adjuster change makes very little difference. After re-valving, the adjusters will be brought into play, and when you make an adjustment, you will be able to notice that it affects the way the way the fork or shock performs.

Another problem with stock suspension is the springs that are used. Often they are progressive, increasing the spring rate with increased compression distance. This means that the valving is correct for only one part of the spring's travel, all other is compromise. If the factory does install a straight-rate spring, it is rarely the correct rate for the weight of the rider with gear. The solution is to install a straight-rate spring that matches the valving for the combined weight of the bike, rider and gear to the type of riding intended.

Remember!

? Always make small adjustments, more is not always better.

? Always keep notes of what you have done.

? Suspension tuning is an art - be patient

Mark Thompson has spent the last 20 Years Racing motorcycles and managing Race Teams. He now runs the Trackbikes website.

---

Motorcycle Tires - Why Should You Care?

One of the most important parts of any vehicle is its tires. Not only are the tires subject to a large amount of wear and tear, but... Read More

Motorcycle Suspension: - A Troubleshooting Guide

Trouble Shooting Suspension Problems.Adjustment locations: ForksRebound adjustment (if applicable) is located near the top of the fork. Compression adjustment (if applicable) is located near the bottom of... Read More

Avoiding Excessive or Uneven Front Tire Wear

All rubber tires wear down over time, whether they're on a motorcycle or automobile. However, you want to watch out for uneven or excessive wear, both of... Read More

The Buzz is All About Mini-Motorcycles

Pocket bikes are miniature motorcycles -- powered, for the most part, by oil- and gas-burning engines similar to those used in chain saws, weed whackers or other... Read More

Kids Like to Ride Motorcycles Too

Roaring up on a motorcycle has a strong draw for all of us who have adopted the biker lifestyle. This draw often hits our children too. I... Read More

Workings of a Motorcycle Muffler Suspension

Motorcycles are becoming more popular because of its convenience and relatively inexpensive cost compared to automobiles. They are capable of the same speeds as cars and can... Read More

Liquid Cooled Minimotos (PocketBikes), How Fast Are They and Are They Affordable?

As the latest craze of Minimoto Madness continues in the United Kingdom. The demand for pocket bikes means that the consumer is now looking for more better... Read More

Minimoto Dirt Bikes, Miniture Motards - The Next Step Up from Battery Powered Toys

As your child grows out of their little bicycle and wants more than a battery powered car to get them 'cruising' along. It can be a head... Read More

Motorcycle Radar Detectors

Standard radar detectors were not built for motorcycles and were never intended to be used on them. Most detectors use an audio device to inform the driver... Read More

Mini Moto Mayhem

Mini Motos have been around in the UK for around ten years now. The first bikes we're cobbled together with parts that were already available. Small 2... Read More

How Do You Make Your Harley Davidson Look And Feel Like An Extension Of Yourself!

How do you make your Harley Davidson look and feel like an extension of yourself!Do you think maybe it's time to do a little customizing for that... Read More

Know Your Mini Moto

The Mini Moto is a small scale replica of the World Super Bikes used by the likes of Valentino Rossi and ex champion Carl Fogarty. The Mini... Read More

Common Mistakes Motorcycle Buyers Make When Looking For a Motorcycle Loan

Whether interest rates are high or low or it's the end of a model year with lots of incentives, motorcycle buyers tend to make the same mistakes... Read More

Personal Scooters are Not Just for Fun

Personal scooters are a highly valuable mobility tool for those who, for health reasons, are unable to move around in public or in their own homes. They... Read More

It?s One Thing for People to Buy Your Product or Service, but It?s Another for Them to Tattoo Your

William Harley and Arthur Davidson, both in their early twenties, built their first motorcycle in 1903. During their first year, the company's entire output was only 1... Read More

So You Want To Be A Custom Bike Builder? Start With A Motorcycle Kit!

So you want to be a custom bike builder? Well friend, before you rush out and buy that motorcycle kit, the one that will set you on... Read More

Women and Motorcycles? You Bet!

To really understand the women and her ride, one needs to go back in history to explore the courageous women who defied the norm and road their... Read More

Frame Slider Design and Selection

Call them crash protectors, crash bobbins, fairing protectors or frame sliders, all these products ultimately seek to do one thing - protect your expensive bodywork or the... Read More

A Great Motorcycle Ride in Mexico: Queretaro

A beautiful ride across cities and places named World Heritage by the Unesco, through an splendid protected natural area and ending in a surrealistic garden by artist... Read More

Motorcycle Accidents: Preparing Your Case

Motorcycle accident is an unexpected occurrence that results to shock and trauma, serious physical injuries and death. The most common reason of a motorcycle accident, which contributed... Read More

Necessity of Motorcycle Parts

If you are one of the many people who consider your bike as invaluable as your family, then we know you're head over heels. We may be... Read More

Auctions and Car Transport: Everything You Need To Know

Everyone has wanted to sell a car at some point and in the age of Internet auctions, there are more options than ever when it comes to... Read More

Motorcycle Helmets - Mind Your Head!

To most riders, motorcycle helmets do not fit into their dream accessory. They feel helmets are restrictive and unnecessary and do not add to their aesthetic appeal.... Read More

Do You Need a Part for Your Harley Davidson Motorcycle?

Need a Harley Davidson Part for your ride?Where do you get a good quality Harley Davidson Part? Can I use an aftermarket part?These questions are not easy... Read More

Save Money on Used Motorcycle Parts

For every motorcycle enthusiast, it is indeed very taxing to maintain bikes as good as new ? its engine running and all its other parts functioning. We... Read More

A Convenient Way to Slash Your Gas Bill

"With oil prices spiraling higher almost every day, people are starting to look for alternative modes of transport," says Michael S. Milstead of Scootertronics. "With scooters, commuters... Read More